Jinan Shunxiang Central Kitchen supplies stainless steel work tables and kitchen sinks for group-meal, prepared-food and seafood plants. Selection turns on.
Measure four numbers before choosing a model
Jinan Shunxiang Central Kitchen Interconnection Technology supplies stainless steel work tables and kitchen sinks to group-meal, prepared-food and seafood plants across Asia, Africa and the Middle East. Work tables and sinks are the easiest items to get wrong, because they usually arrive as one line on a layout drawing: "stainless prep table, qty as required". On site it turns out the sheet is 0.6 mm, the bowl is 180 mm deep, and the drain sits 300 mm from where the floor gully actually is. What gets rebuilt is the wall and the trench, not the table. The figures below follow 2026 build practice for central kitchens and group-meal back-of-house operations, and the clause references are to the current editions of the Chinese standards.
Before you open any catalogue, write down four numbers: sheet thickness, worktop height, bowl depth, and drain outlet size. Once those four are fixed, the model and the size table follow. Everything else is finish.
Sheet thickness: 0.8-1.2 mm is the working band
Commercial stainless work tables and sinks run at 0.8-1.2 mm sheet thickness, in SUS 201 or SUS 304. Below 0.8 mm the purchase price drops, but the bowl underside and the weld seam give out first. Scale and chloride creep into the seam, rust appears from the inside out, and by the time you see it the weld cannot be saved.
Choose 304 or 201 based on what the surface meets: plain water and routine detergent versus brine, acidic sanitiser or a permanently wet room. GB 4806.9-2023 governs migration limits for food-contact metal materials and articles, so ask for the mill certificate and the test report with the shipment, not a verbal claim of "food grade". GB 14881-2013 clause 5.2.1.2 sets requirements for contact surface material and surface condition, and a supplier's promise does not satisfy it.
Worktop height, depth and splashback
The ZZJYGZ series holds a constant 850 mm worktop height, with depths in 600 mm and 700 mm, and lengths from 1000 mm to 2000 mm. Depth is not a free choice. A 700 mm top takes a 500 x 300 mm bowl; a 600 mm top only takes a 400 x 250 mm bowl.
The splashback is about the fall, not decoration. On the ZZJYGZ series the worktop drops 100 mm to the wall line, written as 850 + 100 mm, so wash water does not sit against the wall. Corners are rolled and the joint is sealed properly. Glass bead smeared over a gap is not a seal.

Bowl depth and drain geometry
Bowl depth varies a lot. The GQX-3 knee-operated hand wash sink is 400 x 400 x 240 + 30 mm, the SC-XT is 455 x 455 x 270 + 35 mm, and the XTSC-SP reaches 500 x 400 x (230 + 400) mm. A 240 mm bowl handles hands and tools. It does not handle a full crate of raw produce or a drum of detergent, and that is when you need a deep utility bowl.
Match the drain outlet to the floor gully you actually have. A drainboard must slope toward the bowl, otherwise water spreads across the top instead of running down. The ZZDSDY single-bowl series with drainboard runs from 1000 x 700 x (850 + 100) mm to 1400 x 700 x (850 + 100) mm, with bowls from 400 x 250 mm up to 600 x 500 x 300 mm.
On drainage, GB 14881-2013 clause 5.1.2.4 requires indoor drainage to flow from cleaner areas to less clean areas with no backflow design, and clause 5.1.2.2 requires water-seal gullies at drainage inlets. GB 31654-2021 clause 4.2 sets the same expectation for food service premises.
Knee-operated sinks are not for every position
Knee operation means the hands never touch the tap. GQX-3 is 400 x 400 x 240 + 30 mm in SUS 201/304 at 0.8-1.2 mm sheet. JTSCG-5040 is 400 x 800 x 400 mm, wide enough to stand at the wall. SC-XT is 455 x 455 x 270 + 35 mm and suits a squat working position.
GB 14881-2013 clause 5.1.5.4 requires the tap paired with disinfection facilities at the entrance of a clean work area to be non-hand-operated. GB 31654-2021 clause 4.4.3 requires non-hand-operated taps in special rooms and dedicated operation areas. Elbow, sensor and knee operation all sit inside that requirement.
That does not make knee operation necessary everywhere. A pot sink in the back of a kitchen sees hundreds of uses a day, and the operator is carrying a bowl and bent forward, so a knee pedal is slower than a wrist tap. Knee operation earns its place at the workshop entrance, the tool room, and the wash-down zone, where washes are frequent and short.

Work tables with cabinets and drawers
The YDLZZLM-1460WS is a cabinet work table with sliding doors, 1400 x 600 x (850 + 100) mm, two doors, and custom sizing available. The ZHL-SCG combines a sink and cabinet in one body, 2000 x 1100 x 850 mm, with 2 drawers, 4 cabinet doors, 1 tap and 1 sink.
These two solve services and storage. A 2000 x 1100 mm unit like the ZHL-SCG lets the pipework and cabling underneath disappear into the cabinet. Sliding doors beat hinged doors in a narrow prep line because they need no swing clearance.

Two spec sheets, side by side
| Model | Size (L x W x H) mm | Material / thickness | Use |
|---|---|---|---|
| ZZJYGZ-1070 | 1000 x 700 x 850 | Stainless 201/304 | Prep table with splashback |
| ZZJYGZ-2060 | 2000 x 600 x 850 | Stainless 201/304 | Long prep table, 600 mm deep |
| YDLZZLM-1460WS | 1400 x 600 x (850 + 100) | Stainless, 2 sliding doors | Under-bench storage |
| ZHL-SCG | 2000 x 1100 x 850 | Stainless 201/304 | Sink + 2 drawers + 4 doors |
| GQX-3 | 400 x 400 x 240 + 30 | SUS 201/304, 0.8-1.2 mm | Knee-operated hand wash |
| JTSCG-5040 | 400 x 800 x 400 | Stainless steel | Knee-operated hand wash |
| SC-XT | 455 x 455 x 270 + 35 | Stainless steel | Knee-operated hand wash |
| ZZDSDY-1470 | 1400 x 700 x (850 + 100) | SUS 201/304 | Single bowl + drainboard |
Final specifications depend on the selected model, project requirements and supplier technical documentation. Confirm the size, thickness and drain position against the site layout before the order is released.
Seven acceptance checks
| Check | Method | Suggested verdict |
|---|---|---|
| Sheet thickness | Vernier caliper on the top edge | At least 0.8 mm |
| Worktop height | Steel rule from floor to top | 850 mm, per drawing |
| Level | Spirit level at all four corners | Deviation within 2 mm over 2 m |
| Welds | Visual and tactile, check for spatter | Continuous weld, pickled and passivated |
| Drainage | Flood test, observe 30 min | No leak, no standing water |
| Corrosion | Detergent wipe, 24 h dwell | No discoloration, no pitting |
| Doors and drawers | Open and close 20 times | No binding, no rattle |
Put these seven on the acceptance sheet and agree the numbers against the project. Test with your own drawings and your own dimensions, not the sample unit the supplier brings to the meeting.
Frequently asked questions
Q: Should I specify 201 or 304 stainless steel for work tables?
A: SUS 201 is adequate when surfaces only meet plain water and routine cleaning detergent, provided the sheet stays at 0.8 mm or above. Choose SUS 304 for brine, acidic sanitiser or permanently damp rooms, and require pickled and passivated welds. Mill certificates and test reports must ship with the goods under GB 4806.9-2023.
Q: Is a 240 mm bowl deep enough?
A: Enough for hand washing and scrubbing tools. Not enough for a full crate of raw produce or a detergent drum. A deep bowl costs you under-counter clearance and pushes the bowl bottom close to the floor, which changes the waste run. Mixing jobs means a separate deep utility bowl plus a shallow prep bowl, not one bowl for both.
Q: Are knee-operated sinks mandatory?
A: No. GB 14881-2013 clause 5.1.5.4 and GB 31654-2021 clause 4.4.3 govern taps at entrances and in clean work areas, not the pot sink in the back of a kitchen. Use knee or sensor operation at entrances, tool rooms and wash-down zones, and keep elbow or wrist operation where the operator is handling heavy loads.
Q: How do I match the drain to the site?
A: Measure the distance from the floor gully centre to the wall and to the equipment edge before ordering, and have the outlet position set from that measurement rather than from the product drawing. Check the water-seal gully, the downhill flow direction and backflow protection against GB 14881-2013 clause 5.1.2.
Q: What worktop height should I specify?
A: 850 mm finished height is the common figure. Schools and care kitchens should adjust for the users. Send the worktop height, the splashback fall and the bowl depth together to the supplier; quoting height alone is how mismatched sizes get manufactured.
Related equipment and pages
- ZZJYGZ series stainless work table with splashback: 850 mm top height, 600 and 700 mm depths, 1000-2000 mm lengths, SUS 201/304.
- YDLZZLM-1460WS work table cabinet with sliding doors: 1400 x 600 x (850 + 100) mm, two doors, custom sizing.
- ZHL-SCG sink work table with cabinets and drawers: 2000 x 1100 x 850 mm, 2 drawers and 4 doors, services hidden inside.
- GQX-3 knee-operated hand wash sink: 400 x 400 x 240 + 30 mm, 0.8-1.2 mm sheet, hands never touch the tap.
- JTSCG-5040 knee-operated hand wash sink: 400 x 800 x 400 mm, wall-side standing position for entrances and utility rooms.
- ZZDSDY single bowl sink with drainboard: 1000-1400 mm long, bowls from 400 x 250 mm to 600 x 500 x 300 mm.
- Work tables category: worktops, cabinet tables and two-tier benches in one place for prep line matching.
- Contact us: send site dimensions, water quality and drain positions, and we will size the equipment to the actual layout.
Author: 苏涛;舜翔央厨、华艺智能
"""