\n

News Blog

Deboning vs Fat Trimming Machines: Width, Cut, FAT (2026)

Deboning vs Fat Trimming Machines: Width, Cut, FAT (2026)

HY-103 deboning runs 430 mm width at 1-2 mm on 0.75 kW; DJM-520 trimming runs 520 mm at 0.1-2 mm on 1.1 kW and 5 bar air. Spec table and eight FAT checks.

Jinan Shunxiang Central Kitchen Interconnection Technology is a China supplier of deboning, fat-trimming and dicing machines for slaughterhouse cutting lines, meat processing plants and group-meal suppliers. Two numbers settle the choice: working width and cut thickness. The HY-103 runs a 430 mm width at 1-2 mm and 37 m/min on 0.75 kW; the DJM-520 runs 520 mm at 0.1-2 mm and 38 m/min on 1.1 kW with 5 bar air.

Deboning and fat trimming are different jobs

These machines do different things. The HY-103 lifts the white sinew off bone-adjacent meat at 37 m/min across 430 mm and 1-2 mm, so it eats thick material. The DJM-520 shaves the fat layer and bone chips off the surface at 520 mm and 0.1-2 mm, 38 m/min, so it eats thin layers. Settle which one you are missing before quoting: a cutting line ending at the deboning station wants sinew removal, a prepared-meat plant before the grinder wants surface trimming. Running the wrong machine on the wrong job wastes throughput twice over.

Compute the throughput before you trust the nameplate

Working from swept area is the most honest route. The HY-103 at 37 m/min across 430 mm passes 15.9 m² of cut face per minute. At an average 1.5 mm removal thickness that is roughly 23.9 L/min, or about 1,430 kg of material over the blade per hour. That is theoretical. The sinew actually removed is a fraction of it, and the fraction depends on block shape and where the sinew runs. The DJM-520 sweeps 19.8 m² per minute at 520 mm; at 0.8 mm average trimming thickness that is about 15.8 L/min, roughly 950 kg of material past the blade per hour, again not net output. The only number that goes in a technical agreement is a site trial: 20 kg of typical material, ten minutes, weigh what actually came off.

Dicing is a different convention. The BB-300 is rated at 400 kg/h net, 72 strokes per minute, knife block sizes of 20, 25, 30 and 38 mm, thickness adjustable 2-30 mm, inlet 300 x 50 mm. There the nameplate number is net output and can be written into the contract as it stands.

Three machines, side by side

ItemHY-103 deboningDJM-520 fat trimmingBB-300 dicing
Model / SKUHY-103 / HC-48DJM-520 / HC-28BB-300 / HC-46
Working width430 mm520 mmInlet 300 x 50 mm
Cut thickness1-2 mm0.1-2 mm2-30 mm adjustable
Blade speed / frequency37 m/min38 m/min72 strokes/min
Motor power0.75 kW1.1 kW3.5 kW
Voltage380 V380 V380 V
Compressed airNot stated on the page5 barNot stated on the page
Overall dimensions740 x 960 x 630 mmNot stated on the page950 x 580 x 1080 mm
Machine weight150 kgNot stated on the page320 kg
Material304 stainless steelStainless steel food-contact surfaces304 stainless steel

The DJM-520 product page does not publish overall dimensions or machine weight. Ask the supplier for a drawing with dimensions before quotation, and do not fill in the blanks yourself.

DJM-520 commercial fat trimming machine, 520 mm working width, 0.1-2 mm precision, 38 m/min, 1.1 kW, used on a meat pre-processing line

Feed temperature decides whether the blade can run at speed

Blade speed is not a dial you set anywhere. Chilled meat at 0-4 C cuts cleanly at 1-2 mm. Meat that has thawed with a core above 8 C carries surface water, raises cutting drag, tears the surface, and what comes off the blade is a lump of meat instead of a strand of sinew. Frozen meat goes on only when the core is below 0 C and the edges have tempered without going soft; straight from the freezer it chips the blade edge. Work the schedule back from the cold room curve using the 2-hour rule in GB 31654-2021 clause 7.7.3 (60 C down to 21 C in two hours, then to below 8 C in two more) and the raw material storage temperatures in appendix M. GB 14881-2013 clause 5.1.9.1 requires temperature control facilities and monitoring to suit production; that is a plant requirement, not a machine parameter, but the two have to agree. If the cold room is right and the machine still will not cut, the feed temperature is wrong.

Hygiene design: three places to look

Bone chips and fat debris are what close down a meat plant. GB 14881-2013 clause 5.2.1.3.1 requires production equipment to avoid parts, metal fragments, lubricating oil and other contamination factors getting into food by design and structure, and to be easy to clean, disinfect, inspect and maintain. On these machines that comes down to three checks. First, how the blade-to-baffle gap is arranged, so debris travels with the stroke to the discharge instead of packing into the housing. Second, whether the guard comes apart, so the cleaner can lift the whole knife carrier out instead of reaching into a gap with a brush. Third, whether there is a debris tray and a drain under the frame. On material, check the grade and migration limits against GB 4806.9-2023, published 2023-09-06 and effective 2024-09-06, which replaces GB 4806.9-2016, and ask for the material certificate and test report to travel with the machine.

HY-103 deboning machine, 430 mm working width, 1-2 mm thickness, 37 m/min, 0.75 kW, 304 stainless steel, sinew removal at the end of a cutting line

Air, power and floor space

Trimming machines eat compressed air and the DJM-520 needs 5 bar. The plant practice is a branch line off the header through a filter regulator and drain trap, with the gauge where the operator can read it. Get the air consumption in Nm³/h from the supplier and size the compressor on that number rather than on motor power. On the electrical side, at 380 V three phase with 0.85 power factor and 0.9 motor efficiency, the running currents are about 1.5 A for the 0.75 kW HY-103, 2.2 A for the 1.1 kW DJM-520 and 6.9 A for the 3.5 kW BB-300, so fit 10 A, 16 A and 16 A breakers with 30 mA residual current protection. Space comes from the overall size and the weight: the HY-103 is 740 x 960 x 630 mm at 150 kg, the BB-300 is 950 x 580 x 1080 mm at 320 kg. Above 150 kg nobody shifts a machine by hand, so confirm the floor loading with the building first.

Eight acceptance items

One, run 30 minutes empty and check the knife line holds with no noise beyond the factory limit. Two, run 20 kg of typical material and take 20 measurements, HY-103 at 1-2 mm and DJM-520 at 0.1-2 mm, all inside the agreed band. Three, verify blade speed on a tachometer at 37 m/min and 38 m/min. Four, measure net removal: 20 kg for ten minutes, weighed, with the cycle time matching the line. Five, strip the machine without tools and confirm the guard, knife carrier and debris tray come clean in fifteen minutes. Six, check the material certificate and food-contact test report against GB 4806.9-2023. Seven, prove the utilities: 380 V three phase present, 5 bar available, residual current device test passed. Eight, work every emergency stop and guard interlock and confirm it trips.

Frequently asked questions

Q: Can one machine do both deboning and fat trimming?

A: No. The HY-103 is built for 1-2 mm thick-material sinew removal and will chip on a 0.1 mm trim; the DJM-520 handles 0.1-2 mm surface layers and will stall on a bone-in thick section. The blade speeds differ by only 1 m/min, but the working widths differ by 90 mm and the knife carriers and baffle clearances are not the same parts.

Q: Which is harder on the blades, chilled or frozen meat?

A: Meat at the wrong temperature. A partially thawed block with a core above 8 C carries water, tears instead of cutting, and takes meat with it. Frozen meat fed straight from the freezer chips the edge faster still. The workable window is chilled at 0-4 C, or frozen meat with the core below 0 C and the edges tempered.

Q: Can the DJM-520 really cut at 0.1 mm?

A: The stated range is 0.1-2 mm, but 0.1 mm is the limit case for shaving thin fat, not a production setting. Run trimming at 0.5-1 mm for better yield and block integrity, and verify 0.1 mm point by point on specific cuts.

Q: How do we supply 5 bar in the workshop?

A: A branch line off the header through a filter regulator and drain trap, with the gauge at the operating position. Get the consumption figure in Nm³/h, size the compressor on it, and add up the peak when several trimmers run together.

Q: Can a 380 V machine be rewired for 220 V?

A: Motor, cable and breaker all change. At 220 V single phase the 0.75 kW and 1.1 kW machines draw 4.5 A and 6.5 A, so the feeder and the site distribution have to be redone to the new figures; swapping a plug is not enough. For export projects, set the voltage and plug to the destination market. Final specifications follow the selected model, the project requirements and the supplier technical documentation.

Related equipment and pages

As of 2026 the envelope of this equipment has not moved: 430-520 mm working widths, 0.75-3.5 kW, 380 V three phase, 304 stainless steel on food-contact surfaces. What separates suppliers is the loaded blade curve, blade life and strip-down time. Put those three into the technical agreement and acceptance has something to measure. Send the material, daily output, air supply, voltage and floor dimensions together and the quotation will mean something.

Su Tao; Shunxiang Central Kitchen, Huayi Intelligent